Install the air filter. ● Please consult instructions for cleaning the air filter (The above figure is only for reference, so the intake grille is not included.) on page 12. • How to install or remove the Air- Air-cleaning and Deodorizing filter cleaning and Deodorizing filter maintenance As well as ensuring the maintenance of the dust collecting 1. Remove the dust-collecting unit. Unit, please also take care of the filter.

Merely turning off the unit’s power switch will not completely disconnect the unit from the power source. • TROUBLESHOOTING Symptom Items to check See Page ● Is the Power Supply Plug disconnected its outlet? CHECK ONCE Doesn’t operate at all: MORE ● Has there been a power failure? — ● Has a fuse blown out, or a circuit breaker been tripped?

View and Download Fujitsu ASTB24LDC operating manual. Asta30lfc, Aotr24lfl, Asta24lcc, Asta30lcc, Aotr24lcc, Aotr30lct. Maintenance and/or service of this.

• Cleaning the dust collection unit 5. Install the unit. Install the air filter. ● Please consult instructions for cleaning the air filter (The above figure is only for reference, so the intake grille is not included.) on page 12. • How to install or remove the Air- Air-cleaning and Deodorizing filter cleaning and Deodorizing filter maintenance As well as ensuring the maintenance of the dust collecting 1. Remove the dust-collecting unit. Unit, please also take care of the filter.

Service Manual Kia

Cooling Repairs The following list is a very short brief of some of the things we provide while servicing your equipment. We do perform other important checks and address issues as we find them.

Load Batteries (R03/LR03 × 2) ● Take care to prevent infants from accidentally swallowing batteries. Press and slide the battery compartment lid on the re- ● When not using the Remote Control Unit verse side to open it. For an extended period, remove the batteries to avoid possible leakage and Slide in the direction of the arrow while pressing the. • OPERATION To Select Mode Operation Press the START/STOP button (Fig.6 S).

2 OPERATION TIMER AIR CLEAN Fig. 7 To facilitate explanation, the accompanying illustra- tion has been drawn to show all possible indicators; in actral operation, however, the display will only show those indicators appropriate to the current op- eration. • NAME OF PARTS Fig.

The air conditioner will start operating. Press the MASTER CONTROL button (Fig.6 K) to se- lect the desired mode. Each time the button is pressed, the mode will change in the following order. • To Stop Operation Press the START/STOP button (Fig. The OPERATION Indicator Lamp (red) (Fig. 3 5) will go out.

The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 5) will light. The air conditioner will start operating. Press the MASTER CONTROL button (Fig.6 K) to se- lect the desired mode. Each time the button is pressed, the mode will change in the following order. • To Stop Operation Press the START/STOP button (Fig.

Can anyone with someone with experience with these systems confirm this? Hi there, I've come across similar problems to this. With the resistance/diode check proving fan motor faulty and no lower DC voltage then it looks like the fan motor has taken out the part of the PCB which supplies the lower DC voltages. Just make sure when you are measuring the lower DC voltage you use a neutral from the DC (off the diode bridge is a good one) or else you might get weird readings.

3 5) will go out. About AUTO CHANGEOVER Operation ● When AUTO CHANGEOVER operation first selected, the fan will oper- AUTO: ate at very low speed for about one minute, during which time the unit detects the room conditions and selects the proper operating mode. • AIR CLEANING OPERATION If you wish to eliminate dirt,dust,cigarette smoke, pollen, or just simply purify the air of the room, use the Air Cleaning Mode. Press the START/STOP button (Fig. The OPERATION Indicator Lamp (red) (Fig. 3 5) will light.

● Please consult steps 1 and 2 of cleaning the dust- (Please carry out maintenance on the filter every 6 months.) collecting unit on page 13. • TROUBLESHOOTING In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the elec- WARNING! Trical breaker or disconnect the power supply plug, and consult authorized service personnel. Merely turning off the unit’s power switch will not completely disconnect the unit from the power source. • TROUBLESHOOTING Symptom Items to check See Page ● Is the Power Supply Plug disconnected its outlet?

For an extended period, remove the batteries to avoid possible leakage and Slide in the direction of the arrow while pressing the. • OPERATION To Select Mode Operation Press the START/STOP button (Fig.6 S). The indoor unit’s OPERATION Indicator Lamp (red) (Fig.

KEEP THIS OPERATION MANUAL FOR FUTURE REFERENCE FUJITSU GENERAL LIMITED OPERATING MANUAL P/N-01 Indoor Unit ASTB24LDC Outdoor Unit AOTS24LDC HEAT & COOL MODEL (REVERSE CYCLE) ROOM AIR CONDITIONER WALL MOUNTED TYPE R410A REFRIGERANT This Air Conditioner contains and operates with refrigerant R410A and Polyol Ester oil. THIS PRODUCT MUST ONLY BE INSTALLED OR SERVICED BY QUALIFIED PERSONNEL. Refer to Commonwealth, State, Territory and local legislation, regulations, codes, installation & operation manuals, before the installation, maintenance and/or service of this product.

1 MANUAL AUTO Fig. 2 OPERATION TIMER AIR CLEAN Fig. 7 To facilitate explanation, the accompanying illustra- tion has been drawn to show all possible indicators; in actral operation, however, the display will only show those indicators appropriate to the current op- eration. • NAME OF PARTS Fig. 1 Indoor Unit Fig. 6 Remote Control Unit 1 Operating Control Panel (Fig.

● Please consult steps 1 and 2 of cleaning the dust- (Please carry out maintenance on the filter every 6 months.) collecting unit on page 13. • TROUBLESHOOTING In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the elec- WARNING! Trical breaker or disconnect the power supply plug, and consult authorized service personnel. Merely turning off the unit’s power switch will not completely disconnect the unit from the power source. • TROUBLESHOOTING Symptom Items to check See Page ● Is the Power Supply Plug disconnected its outlet? CHECK ONCE Doesn’t operate at all: MORE ● Has there been a power failure?

• THIS PRODUCT MUST ONLY BE INSTALLED OR SERVICED BY QUALIFIED PERSONNEL. Refer to Commonwealth, State, Territory and local legislation, regulations, codes, installation & operation manuals, before KEEP THIS OPERATION MANUAL the installation, maintenance and/or service of this product. FOR FUTURE REFERENCE FUJITSU GENERAL LIMITED P/N-01. • CONTENTS SAFETY PRECAUTIONS. 1 ADJUSTING THE DIRECTION OF FEATURES AND FUNCTIONS.

Load Batteries (R03/LR03 × 2) ● Take care to prevent infants from accidentally swallowing batteries. Press and slide the battery compartment lid on the re- ● When not using the Remote Control Unit verse side to open it. For an extended period, remove the batteries to avoid possible leakage and Slide in the direction of the arrow while pressing the. • OPERATION To Select Mode Operation Press the START/STOP button (Fig.6 S). The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 5) will light.

Online Auto Repair offers service repair manuals for your Ducati Multistrada - DOWNLOAD your manual now! Complete list of Ducati Multistrada motorcycle service repair manuals: • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •.

— ● Has a fuse blown out, or a circuit breaker been tripped? • OPERATING TIPS Temperature and Humidity Range Cooling Mode Dry Mode Heating Mode Outdoor temperature About -10 to 43 °C About -10 to 43 °C About –15 to 24 °C Indoor temperature About 18 to 32 °C About 30 °C or less About 18 to 32 °C ●.

• THIS PRODUCT MUST ONLY BE INSTALLED OR SERVICED BY QUALIFIED PERSONNEL. Refer to Commonwealth, State, Territory and local legislation, regulations, codes, installation & operation manuals, before KEEP THIS OPERATION MANUAL the installation, maintenance and/or service of this product. FOR FUTURE REFERENCE FUJITSU GENERAL LIMITED P/N-01. • CONTENTS SAFETY PRECAUTIONS. 1 ADJUSTING THE DIRECTION OF FEATURES AND FUNCTIONS.

2 AIR CIRCULATION.11 NAME OF PARTS.3 SWING OPERATION.12 PREPARATION.5 COIL DRY OPERATION. 12 OPERATION.

For checking the 5V you can remove a probe plug and just measure across the two pins on the PCB. The fact that the high voltage DC is there proves that part of the circiut through the ACTPM and all that is sound. Although the fuse is there for protection it doesn't always protect the PCB. Cheers, Andy.

● When removing and replacing the air filters, be sure not to touch the heat exchanger, as per- sonal injury may result. • CLEANING THE PLASMA AIR CLEANING FILTER Before cleaning the plasma filter unit, be sure to turn off the power supply to the air conditioner. Electric shock may result. ● Make sure the plasma filter unit is properly mounted before cleaning or performing other tasks CAUTION! • Cleaning the dust collection unit 5. Install the unit.

Load Batteries (R03/LR03 × 2) ● Take care to prevent infants from accidentally swallowing batteries. Press and slide the battery compartment lid on the re- ● When not using the Remote Control Unit verse side to open it.

2 OPERATION TIMER AIR CLEAN Fig. 7 To facilitate explanation, the accompanying illustra- tion has been drawn to show all possible indicators; in actral operation, however, the display will only show those indicators appropriate to the current op- eration. • NAME OF PARTS Fig. 1 Indoor Unit Fig. 6 Remote Control Unit 1 Operating Control Panel (Fig. 2) J SLEEP button 2 MANUAL AUTO button K MASTER CONTROL button ● L AIR CLEAN button When kept on pressing the MANUAL AUTO button for more than 10 seconds, M SET TEMP. • PREPARATION CAUTION!

• Retighten all flare nuts to eliminate any potential gas leaks • Go over all electrical connections and retention them • Test current draw of electrical components • Go over all of the duct work to make sure there are no air leaks • Check correct airflow throughout the system To view the full lists for each equipment type, please click more info below.

Can anyone with someone with experience with these systems confirm this? Hi there, I've come across similar problems to this. With the resistance/diode check proving fan motor faulty and no lower DC voltage then it looks like the fan motor has taken out the part of the PCB which supplies the lower DC voltages. Just make sure when you are measuring the lower DC voltage you use a neutral from the DC (off the diode bridge is a good one) or else you might get weird readings. For checking the 5V you can remove a probe plug and just measure across the two pins on the PCB. The fact that the high voltage DC is there proves that part of the circiut through the ACTPM and all that is sound. Although the fuse is there for protection it doesn't always protect the PCB.

2) J SLEEP button 2 MANUAL AUTO button K MASTER CONTROL button ● L AIR CLEAN button When kept on pressing the MANUAL AUTO button for more than 10 seconds, M SET TEMP. • PREPARATION CAUTION!

• NAME OF PARTS Fig. 1 MANUAL AUTO Fig.

CHECK ONCE Doesn’t operate at all: MORE ● Has there been a power failure? — ● Has a fuse blown out, or a circuit breaker been tripped? • OPERATING TIPS Temperature and Humidity Range Cooling Mode Dry Mode Heating Mode Outdoor temperature About -10 to 43 °C About -10 to 43 °C About –15 to 24 °C Indoor temperature About 18 to 32 °C About 30 °C or less About 18 to 32 °C ●.

6 CLEANING AND CARE. 13 AIR CLEANING OPERATION. • FEATURES AND FUNCTIONS INVERTER OMNI-DIRECTIONAL AIR FLOW (SWING OPERATION) At the start of operation, a large power is used to bring the room quickly to the desired temperature. Afterwards, the Three-dimensional control over air direction swing is possi- unit automatically switches to a low power setting for eco- ble through dual use of both an UP/DOWN air direction swing nomic and comfortable operation. • NAME OF PARTS Fig. 1 MANUAL AUTO Fig.

Install the unit. Install the air filter. ● Please consult instructions for cleaning the air filter (The above figure is only for reference, so the intake grille is not included.) on page 12. • How to install or remove the Air- Air-cleaning and Deodorizing filter cleaning and Deodorizing filter maintenance As well as ensuring the maintenance of the dust collecting 1. Remove the dust-collecting unit.

The air conditioner will start operating. Press the MASTER CONTROL button (Fig.6 K) to se- lect the desired mode. Each time the button is pressed, the mode will change in the following order. • To Stop Operation Press the START/STOP button (Fig.

(If the unit is already in operation, please proceed to step 2.) Press the AIR CLEAN button (Fig. • TIMER OPERATION Before using the timer function, be sure that the Remote Control Unit is set to the correct current time (☞ P. To Use the ON timer or OFF timer Press the START/STOP button (Fig. 6 S) To Cancel the Timer (if the unit is already operating, proceed to step 2). • SLEEP TIMER OPERATION Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operate is stopped.

3 5) will light. The air conditioner will start operating. Press the MASTER CONTROL button (Fig.6 K) to se- lect the desired mode. Each time the button is pressed, the mode will change in the following order. • To Stop Operation Press the START/STOP button (Fig. The OPERATION Indicator Lamp (red) (Fig.

I have just got back to this. I disconnected the fan motor and the 350V DC supply returned to the main PCB. With this done the unit still doesn't run. I measured the voltage rails on the PCB and the 5V only has 0.5V. The fan measured approx 15 ohms between the red and black and approx 60 ohms between the white and black. When using the diode check the readings are the same no matter which way you have the leads. So it looks to me like the fan motor is faulty and has taken out the main PCB.

Press the START/STOP button (Fig. The OPERATION Indicator Lamp (red) (Fig. 3 5) will light. (If the unit is already in operation, please proceed to step 2.) Press the AIR CLEAN button (Fig. • TIMER OPERATION Before using the timer function, be sure that the Remote Control Unit is set to the correct current time (☞ P. To Use the ON timer or OFF timer Press the START/STOP button (Fig.

The OPERATION Indicator Lamp (red) (Fig. 3 5) will go out.

About AUTO CHANGEOVER Operation ● When AUTO CHANGEOVER operation first selected, the fan will oper- AUTO: ate at very low speed for about one minute, during which time the unit detects the room conditions and selects the proper operating mode. • AIR CLEANING OPERATION If you wish to eliminate dirt,dust,cigarette smoke, pollen, or just simply purify the air of the room, use the Air Cleaning Mode. Press the START/STOP button (Fig. The OPERATION Indicator Lamp (red) (Fig. 3 5) will light. (If the unit is already in operation, please proceed to step 2.) Press the AIR CLEAN button (Fig. • TIMER OPERATION Before using the timer function, be sure that the Remote Control Unit is set to the correct current time (☞ P.

• THIS PRODUCT MUST ONLY BE INSTALLED OR SERVICED BY QUALIFIED PERSONNEL. Refer to Commonwealth, State, Territory and local legislation, regulations, codes, installation & operation manuals, before KEEP THIS OPERATION MANUAL the installation, maintenance and/or service of this product. FOR FUTURE REFERENCE FUJITSU GENERAL LIMITED P/N-01. • CONTENTS SAFETY PRECAUTIONS. 1 ADJUSTING THE DIRECTION OF FEATURES AND FUNCTIONS.

• ADJUSTING THE DIRECTION OF AIR CIRCULATION ● Adjust the up, down, left, and right AIR directions with the AIR DIRECTION buttons on the Remote Control Unit. ● Use the AIR DIRECTION buttons after the Indoor Unit has started operating and the airflow-direction louvers have stopped moving. • SWING OPERATION Begin air conditioner operation before performing this procedure. To select SWING Operation Press the SWING button (Fig.

Trical breaker or disconnect the power supply plug, and consult authorized service personnel. Merely turning off the unit’s power switch will not completely disconnect the unit from the power source. • TROUBLESHOOTING Symptom Items to check See Page ● Is the Power Supply Plug disconnected its outlet?

Press the START/STOP button (Fig. The OPERATION Indicator Lamp (red) (Fig. 3 5) will light.

To Use the SLEEP Timer To Cancel the Timer: While the air conditioner is operating or stopped, press the Use the TIMER MODE button to select SLEEP button (Fig. • ADJUSTING THE DIRECTION OF AIR CIRCULATION ● Adjust the up, down, left, and right AIR directions with the AIR DIRECTION buttons on the Remote Control Unit. ● Use the AIR DIRECTION buttons after the Indoor Unit has started operating and the airflow-direction louvers have stopped moving. • SWING OPERATION Begin air conditioner operation before performing this procedure.

1 Indoor Unit Fig. 6 Remote Control Unit 1 Operating Control Panel (Fig. 2) J SLEEP button 2 MANUAL AUTO button K MASTER CONTROL button ● L AIR CLEAN button When kept on pressing the MANUAL AUTO button for more than 10 seconds, M SET TEMP. • PREPARATION CAUTION!

The SWING Display (Fig. 7 f) will light. Each time the SWING button is pressed, the swing operation will change in the following order. • CLEANING AND CARE ● Before cleaning the air conditioner, be sure to turn it off and disconnect the Power Supply Cord. ● Be sure the Intake Grille (Fig. 1 8) is installed securely.

Press and slide the battery compartment lid on the re- ● When not using the Remote Control Unit verse side to open it. For an extended period, remove the batteries to avoid possible leakage and Slide in the direction of the arrow while pressing the. • OPERATION To Select Mode Operation Press the START/STOP button (Fig.6 S). The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 5) will light.

Although the fuse is there for protection it doesn't always protect the PCB. Cheers, Andy.

To select SWING Operation Press the SWING button (Fig. The SWING Display (Fig. 7 f) will light. Each time the SWING button is pressed, the swing operation will change in the following order.

For checking the 5V you can remove a probe plug and just measure across the two pins on the PCB. The fact that the high voltage DC is there proves that part of the circiut through the ACTPM and all that is sound.

I have just got back to this. I disconnected the fan motor and the 350V DC supply returned to the main PCB. With this done the unit still doesn't run. I measured the voltage rails on the PCB and the 5V only has 0.5V. The fan measured approx 15 ohms between the red and black and approx 60 ohms between the white and black. When using the diode check the readings are the same no matter which way you have the leads. So it looks to me like the fan motor is faulty and has taken out the main PCB.

To select SWING Operation Press the SWING button (Fig. The SWING Display (Fig. 7 f) will light. Intel graphics 3600 windows 10.

Unit, please also take care of the filter. ● Please consult steps 1 and 2 of cleaning the dust- (Please carry out maintenance on the filter every 6 months.) collecting unit on page 13. • TROUBLESHOOTING In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the elec- WARNING!